For arts and crafts and quick, easy patch-ups, nothing beats a hot glue gun. Unlike other adhesives, hot glue goes on smoothly, dries fast and holds firm when applied to all sorts of different surfaces. While its hold is not the strongest, it can be used to bond a greater diversity of materials than almost any other glue. Using a hot glue gun is a breeze as long as you follow a few basic steps and keep safety guidelines in mind.
1. Consult the owner's manual. Go over the owner's manual for information about safely operating your glue gun. Take note of the different components of the glue gun and how they're supposed to function. The instruction manual should be able to tell you whether your glue gun will begin heating up automatically or needs to be turned on and off, how long it typically takes to warm up, and what materials it's recommended for.
Be sure to read through the safety warnings carefully to reduce the risk of accident or injury while using the glue gun.
Your manual should also specify exactly what size or type of glue stick you'll need.
2. Inspect the
glue gun for signs of damage. Before plugging in or using the glue gun, look over the body to check for cracking, splitting, chipping or any other indications of damage. Make sure you also take a look at the electrical cord to see if there’s any frayed or broken wires. It can be very dangerous to operate a glue under under these conditions.
Because of their electrical and heating elements, a malfunctioning glue gun can be extremely hazardous to use.
3. Make sure the nozzle is free of old glue residue. There should be a clear path for the melted glue to emerge from the tip of the glue gun. If necessary, remove the nozzle and wipe it down with a piece of aluminum foil to take off dried glue, or use a toothpick to clean out the hole. Your glue gun should always be free of excess residue from past projects before each use.
Always make sure the glue gun is unplugged before handling or removing the nozzle.
Never use water to clean a glue gun. In the worst case scenario, you may simply have to wait until the glue gun warms up enough for the old stuck-on glue to drip off.
4. Load a glue stick into the back of the gun. Take a fresh glue stick and place one end into the circular opening in the back of the gun. Slide it in until it stops. If there is already a partially used glue stick in the gun, finish that stick before inserting a new one. Your glue gun does not need to be loaded with a new stick for each project.
Most glue sticks are uniformly sized and made to fit any glue gun model. Check the instructions or specifications of your glue gun when buying replacement glue sticks just to be on the safe side.
5. Plug the glue gun’s cord into an electrical outlet. Locate an electric outlet in the wall nearest to where you’ll be working on your project. Stick the glue gun’s electric cord into the socket. The glue gun’s heating element will automatically begin to warm the glue stick inside, so don’t touch the nozzle or leave the glue gun unattended once it has been plugged in. Ensure you’re your glue gun is upright in its stand to avoid accidents.
Again, check the electrical cord for any signs of damage or deterioration before plugging it in. An cord in bad condition can present a possible fire risk.
Some glue gun models are cordless, giving you more freedom to choose where and how you work. If you can't find one of these, try using an extension cord to increase your range within your work area.
1. Wait for the glue to heat up. Give the glue gun a couple minutes to soften the glue. Once it's been sufficiently melted, the glue will ooze out when you pull the trigger. For most glue guns, the heating process will take around two minutes. Larger and industrial-grade glue guns may require up to five minutes to heat the glue enough to make it easily dispensable.
Some glue guns will have on/off switches, while others won’t. If your model does, it will need to be placed in the “on” position before it will begin heating up the glue. Otherwise, it will start warming as soon as it is plugged in.
Rest the glue gun on the wire support stand at its base when it’s not in use. Never lay an active glue gun on its side.
2. Lightly squeeze the trigger to release the melted glue. Aim the nozzle of the glue gun downwards and place it close the item you’ll be gluing. Gently squeeze the trigger of the gun until melted glue begins to emerge from the nozzle. Glue directly onto the item’s surface, leaving the nozzle in contact. Apply the glue smoothly in dots, swirls or straight lines.
Place a piece of scrap cardboard or foil beneath the object you’re gluing to catch stray strands of glue.
Try gluing a few pieces of throwaway material to get a feel for your glue gun before using it for projects that require precision.
If possible, wear a pair of gloves while working with hot glue to protect your hands from the heat and mess.
3. Only use as much glue as you need. Start with a modest amount of glue and then determine whether you need more. A little glue goes a long way. The melted glue will flow fairly quickly once the trigger is pulled, and it can be easy to use too much if you’re not careful. Avoid saturating the item you’re gluing or applying the glue in messy globs. Glue can set up rather quickly, so only use as much as you need as you go.
Attaching Styrofoam letters to diorama will only take a small dot, for instance, while you might want to add more glue in a zig-zag or spiral pattern to securely hold objects with large surface areas or heavy parts.
.jpg)
Hot glue is meant to be applied somewhat thickly, but using an excessive amount can cause softer surfaces to grow stiff and may be unsightly.
Chances are that if you use too much, at some point you'll need to know how to remove hot glue.
4. Wait for the glue to dry. Remove the nozzle from the item you just finished gluing. If the glue gun model you’re using has an on/off switch, flip it to the “off” position and set it aside. Allow the glue to dry for several minutes. The bond between the glued surfaces will solidify as the glue sets up. It can be helpful to hold your items with your hands or a clamp as the glue sets for a tight bond.
.jpg)
.jpg)
.jpg)
.jpg)
.jpg)
